We make a milling machine from a conventional drill

Fans of making something at home often ask the question: “Is it possible to assemble a router bit from a drill with your own hands?”. Such an idea has a fairly solid foundation in the form of the high cost of a professional profile tool. The price of a modern milling machine can seriously hit your home budget, and they will not have to be used very often. It turns out to make such a device yourself quite real.

Use of milling machine

Most often, such a tool is very useful when repair of a country house or building a private cottage. With such a unit, hard woodworking can be done right at home. You will be available:

  • milling of wooden parts;
  • edge formation;
  • creation of special fittings;
  • other woodworking;

A large number of advantages do not always outweigh the overpriced price of the tool, which at the end of the repair will gather dust in the closet. Therefore, a homemade manual router has become increasingly popular with homeowners.

Device manufacturing

Before you proceed directly to the assembly procedure, you need to take care of a special stand - milling table. This element can be assembled from thick plywood or chipboard panels.

 Holder

Get suitable details:

  • sheets of plywood or chipboard with a thickness of at least twelve millimeters;
  • four support bars;
  • clamp to fasten the drill on the table ;.

Getting down to the build process. Make holes for the bolts in the main vertical wall and fasten the guide clamp.

After that, make a round hole in the middle of the backing sheet. Professionals are advised to use for this purpose. electric jigsaw, but a simple hacksaw will do. The final stage is the connection of all parts into a single structure using screws or superglue. The table is ready, the most important thing is to make the router itself.

 Drill with holder

The main elements of the device

The basis of a good milling machine is electric drive. Its power should not be below 500 watts. Calculate this figure depending on the thickness of the wooden parts that you plan to process. The most suitable option are a drill, punch or grinder with a capacity of from 500 to 1100 watts. The best choice, in terms of price and reliability, is a drill.

When buying, you should pay special attention to the quality characteristics of the drill, because later it can be used for its intended purpose.

For assembling the entire system you will need the following components:

  • good electric drill;

 Electric drill

  • cutter - an item that is purchased separately in a specialty store;

 Milling cutter

  • special cartridge for fastening.

 Cartridge

The last part is connected to the drill with adapterwhich should be picked up separately, depending on type of a mill. To install such an adapter is problematic, but it is quite possible at home.

Assembly sequence

When making a milling machine, it is necessary to follow some guidelines that will allow you to avoid mistakes. Particular attention should be paid to lift to adjust - it is fixed on the table top to compensate for the speed of turns.For the manufacture of this part using dense plywood.

It is very important to achieve solidity in the design, avoid using straps, cables, small nails and slats. The cutter itself is then installed on the motor shaft. As a result, the elevator will include:

  • carriages;
  • case, which will be the main load;
  • threaded axle;
  • fixing attachment;
  • sliding type runners.

As the threaded axis rotates, the carriage moves with the engine. It moves it up or down along the axis line. Runners are designed to limit and guide movement.

Height restrictions must be set in advance while the device is stationary. Fixing the locking elements in the desired position, you will protect yourself and your work.

It is imperative to follow smooth carriage movement. Get the most stable position to eliminate the occurrence of defects and irregularities in the processing of wood. Experienced craftsmen make special gears and pivotal levers, which are then included in the overall system for control.

So, following simple tips, you can assemble a router from a conventional drill.Carefully customize parts and use only quality materials. Do not try to save on the drill, remember, when the construction is over, you can disassemble the machine and use it for its intended purpose. Do not rush to throw out the table and the elevator after - they can be disassembled into separate elements and compactly packed in a box until the next repair. That is why professionals use to connect only the construction screws.

Comments: 0
Continuing the theme:

Video camera

Home cinema

Music Center